3D-cканер VI-930 Konica Minolta. Панкратов В.Б. - 24 стр.

UptoLike

Составители: 

46
Сообщения об ошибках (продолжение)
Сообщение Причина Действия
The element has
no image/The
elements have no
image. (An alarm
will be heard if
the shortcut key is
used.)
The command was selected even though
only the polygon mesh elements that
were defined without copying images or
elements other than polygon mesh
elements were selected
Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
If both polygon mesh
elements with images and
those without images are
selected, this error message
will not be displayed for
those elements that do not
contain images
The element has
no image. (An
alarm will be
heard if the
shortcut key is
used.)
The selected element did not have any
images when the command was selected
Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
The size of this
image is different
from the size of
selected image
The size of the selected image was
different from that of the image you tried
to load, due to replacement of textures
Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
There are no
points. The
element will be
removed. (“File
name”)
No data points were contained Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно. The element will be
selected
This element does
not have multiple
images
You attempted to execute the command
on an element that has only a single
image
Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
This Shortcut key
about [Command
Name] is an
invalid
combination. It
will be reset!
The shortcut key combination you
attempted to set is not supported by this
command
Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
47
Сообщения об ошибках (продолжение)
Сообщение Причина Действия
This Shortcut key
about [Command
Name] is exist!
Please set
another!
The same shortcut key had already been
assigned when you tried to assign it
Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
This version of
scene file is not
supported
The [Open] button was clicked even
though a scene file saved by the Utility
Software VI-S1 had been selected
Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
Too Small Mesh.
We can’t get
enough
information for
registration
Among selected elements, at least one
element that is composed of less than a
certain number of constituent points
exists
Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
Turntable not
found
The rotary stage is not connected to the
digitizer or it is not turned ON
Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
Value must be 0 <
value < 10000
A value outside the allowable range was
entered
Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
Value must be –
100000 < value <
100000
A value outside the allowable range was
entered and the OK button was clicked
Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
VIVID busy The SCSI command did not complete Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
VIVID not found VIVID (VI) series digitizer is not turned
ON, cables are disconnected, or the SCSI
device driver setting is not correct
Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
“Element name”
Zero or few
polygons found.
Skip making LOD
The selected element has an excessively
small number of polygons
Щелкните на кнопке [OK],
чтобы закрыть диалоговое
окно.
5.1 Использованная литература
1. Polygon Editing Tool ver. 2.2. Instrstion Manual, Konica-Minolta,
2006
2. Non-contact 3D digitizer VIVID 910/VI-910